Logo

P1104 Engine Trouble Code

P1104 Engine

When you check engine light came on code P1104 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P1104 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

P1104 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

P1104 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
1
Fuel And Air Metering
1
Engine Oil Temperature Sensor Malfunction
0
Cylinder 10 Contribution/balance Fault
4
Clutch Position Sensor Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P1104 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P1104 OBD-II Trouble Code Mass Air Flow Ground Malfunction is one of the definitions for the P1104; however your vehicles manufacturer may have a different definition for the P1104 code. Please check below for your specific ma P1104 code. Engine Oil Temperature Sensor Malfunction and Cylinder 10 Contribution/balance Fault causes most of code P1104.

Reason For P1104 Code

The reason of P1104 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.

P1104 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair P1104 Code

Before starting let's see P1104 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P1104 code stored in the ECU.
  • Technicians will note P1104 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The fluid pressure sensor provides the PCM with the data necessary to monitor the transmission performance. If the fluid pressure increases, the electrical voltage reading from the pressure sensor will increase; if the pressure decreases, the voltage decreases.

This can result in damage to engine parts over duration of time. We consider that you seal the engine leaks right away if possible. Rising fuel usage can often be associated to a defect in how your engine generates fuel. When matched up with a check engine light in sight and other engine-associated symptoms, the issue can be even more critical. If you see that your vehicle is consuming more fuel, have it inspected and repaired by a mechanic.

Sometimes P1104 code comes with P110400 code.

Diagnosis Of Engine Error OBD Code P1104

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P1104 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P1104 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.